@tango
Active 6 years, 3 months agoForum Replies Created
-
Posts
-
After a little playing with ideas, I am thinking about getting the foam reshaped something like this?
The Other idea that I am working on is to do a 2nd Café Racer seat. But make this a Single seat conversion, I could do this by using a modified standard B tail unit and moving it forward and make a seat pan out of sheet metal to fit in the gap and fit foam in and have to custom covered?
Now then… Next a Seat!?
I have an idea that I would like to do a “Ton Up Two Up” Café Racer.
One that if required could take a pillion. After all I am trying to get my wife out on the odd occasion and I think it could be fun to turn up to a local bike meet on a Café Racer for two!.
Now Philpass came up with a nice idea and it is based on a standard seat! and it was supplied with all the spare parts when I 1st bought this project! I may well use this on the bike?
He had trimmed a standard tail section and fitted it to the metal rim of a normal seat!
Next Problem Encountered with fitting Café Racer Bars as you can see from the above photo. Is the fact that because the Café Bars move forward bay wrapping around the clocks! Your front indicators are now right where your controls need to be!
So Yes you guessed it! Back to Ebay to find some small in keeping smaller Indicators that can be fitted somewhere that wont get in the way, but can still be seen.?
I have found some I think?, I’m just waiting for those to arrive.
Ok a week or so later I Did manage to find a set of Café Racer bars that met all of my requirements and they were ordered up!
When they arrived the were offered up to the bike and I was happy with the fact that the were big enough for the switch gears to fit, and they went around the clocks and looked big enough for the bike!
Well The 1st step in my book was to find some Café Racer Bars!
Easy Job you think! Well Not so straight forward as you think.
I went on Ebay found a set that I liked the look of and with the press of a button they were on there way to me!.
But alas when they arrived and I tried to fit them to the bike! I found that there were a Few things I should have taken into consideration!
1) Are the Bars wide enough to take the Master cylinder and switch gears.
2) Are the Bars wide enough to fit around the bikes clocks!
3) Are the Café Bars wide enough as not to look stupid when you fit them to the bike!
The answer to all 3 of these questions in my case was No!! 🙁
So Alas Back to the drawing board and Back to searching Ebay!
😕Well Now…. I have a little bit of a confession to make here!
But in my defence it was not! my doing!
The above photos of the bike are with in its more Normal Standard Original look. But those Die Hard Twin gurus on here will notice that the rear mud guard is not a Kawasaki Unit, I had to use one that fitted the bike and would be useful for my needs later in the Transformer build.
I had to use this imposter of a mud guard because somebody!! (Philpass):-D had already cut part of my beloved Early B1 frame off!! 😕 😥
The part that holds the rear tail light! 🙄
So that is why I had to use that rear mud guard, and for the Record!! I am sticking to my Promises made at the 2nd International Twin Meet! and I will Not cut up the frame!
But I will add at this point! That I do still have the section that was cut off & I will Keep hold of it and not throw it away! 😉
So Now for my Ideas as to the Transformer bit!.
I have managed to find some Café Racer bars that suit the look that I’m going for.
To me a café racer is not a major overhaul to the original motorbike, but more what the average 1950’s/60’s lad could afford to do to a motorcycle that had been handed down to them, normally from their father that used it for commuting to work! So I’m not going for anything major in the rebuild department!
Besides when I was at the 2nd International Twin Meet in Belgium, I told (I’m Sorry I can’t remember his name!) a member of the German Forum, That I would not Cut my frame up! as he went white when he looked at my frame number? (Apparently its an early one!?) and I told him I was going to do a Café Racer with it! I was most sternly told that I could not do this with this Frame!
So Promises were made that I would not cut the Frame up or modify the bike so that it could not be put back to original!
😳
A reasonably standard looking Twin.
With the capability of Carrying a lot of luggage! Easily enough to be able to tour with!
