Forum Replies Created
-
AuthorPosts
-
beachcomberParticipantWhat’s that? best laid plans etc……
The frame and other parts were due in this week for powder coating – but the PC place has been inundated with a rush job from a major manufacturer [ ? ]. So, all nicely tucked up in the back of my Citroen and they have promised for next week. Ah well, I only started this project 12 months ago !
On the good news front, my pal got me a set of the isolator gaskets [ anti-vibe ]for the Weber. Downside – they only come in sets of 4 [ twin Webers ! ]
I’ll keep the spare set by in case KK wants to go ahead with a conversion.
beachcomberParticipantHA………no she’s not nervous around our Dobe – she’s a big softie [ so’s the dog, boom, boom ].
I’ll get all three made up and I’ll certainly earmark one for you so you can make a final decision.
Please take a close look at the rough mock up to see where the Weber is placed. From memory there is normally an air filter ass’y where the bell mouths protrude back into the frame ? Obviously that will not be needed. If you do want to run filtration – then K&N / a.n.other will do. When I did the mock up, I left the OEM inlet stubs in place to give me a rough idea of spacing. The beauty of this conversion is that it can all be put back to standard if required.
When the final mock up is done, I’ll post up so peeps can see exactly where everything fits.
Ideally 38mm / 40mm Weber for the job. Rebuild kits are silly cheap [ sub £30 ] and you will need two rubber isolator gaskets – readilly available [ as are jets etc.]. They take care of any vibrations. Solex and Dellorto also make similar carbs – cheaper, but parts not so easy to come by.
I used a 40 DCOE on my sidecar race bike [ 650 Triumph engine ] back in the 60’s. It was a piece of cake to tune [ effectively ONE carb ]and I never suffered from fuel surge as some outfits did !
Please be aware this is NOT something that will happen rapidly – as I am always at the mercy of others when it comes to fabrication / welding.
Final pic [ BSA Street Scrambler ] is the general loook I’m after
beachcomberParticipantThanx for the kind thoughts KK.
My wife is well on the mend now – but still nervous around dogs [ we have a GBFO Doberman ! ]
Re: Weber intake, I’ll do them at cost plus 10% to cover my development, running around, etc.
The set [ 3 flanges – 2 x intake 1 x Weber ] cost me £39 inc. vat.
There’s only 2 x small lengths of tube [ minimal cost ] plus the cost of welding them up.
beachcomberParticipantWell that went pear shaped !
First off – long break at our place in Saxony – just didn’t want to come back !
Came back raring to go – frame mods finished [ courtesy of a friend in the end ] and all parts finally ready for powder coating.
THEN, my Wife was attacked by a friend’s [?? ] dog. Ten days in hospital and two operations …..
So, again not a lot happened in my garage while all that was going on.
On a positive note – the same friend who finished the frame mods has volunteered to weld up the Weber intake manifold. Just have to decide whether to get him to make up the three sets – I had to order a minimum of 3 sets of flanges from the lazer cutter.
I also found a local Cafe Racer parts supplier who has exhaust pipes made for him. He’s prepared to loan me a set of unchromed BSA Spitfire high level pipes to see if they can be modded for my bike. I have the exhaust flange stubs [ thanx Hoggy ].
I AM getting a clear picture in my mind now for the “look”.
Red frame, forks, yokes, swingarm, prop stand. Yellow tank, seat cowl, mudguards etc. MAybe some graphics. Maybe Red wrinkle finish engine [ if not – Black ]. Gold wheels. Black perforated leather seat upholstery on my H-D XR750 seat base.
No lights [ except brake light ]and Flat track style “number plates”.
Just got to make it happen now !
beachcomberParticipantDid that REALLY take me 2 weeks to get round to cutting and fettling the seat /tray mounting strap ?????????? Well – yes !
Done now, so I unpacked the brand new Aldi [ £29.00 ] arc welder ready to attach said strap -only to realise that the fuse box that feeds my garage has 15amp capacity. Arrghh, after the 3rd time it tripped I just gave up and watched the World Superbike racing !
This week – I’ll get some 30 amp fuses and get the welding done, then bits off to shot blasters.
beachcomberParticipantManaged to score some 25mm x 3mm steel strip at my pal’s workshop at the weekend. I can get the underseat mounts made now. They’ll double up as the mounts for the electrics tray I’ll be putting under the seat – then it’ off to shotblasters nest week with my pal’s stuff.
beachcomberParticipantYes – that’s the going rate round here, but my pal has loads of repeat work there [ Jag replica chassis’ and parts ] so gets a good deal. I’ll just “slide” my stuff in with his next order !
Ditto with the wire wheels for the tracker – £20 a wheel blasted and powdercoated Gold.
beachcomberParticipantGot a good deal for the shotblasting through my pal who builds the replica Jags – Frame / swingarm and sidestand £15 !!!
That’ll be off this week together with my TR1 Cafe Racer frame/swingarm.
beachcomberParticipantThe frame [ + s/a, sidestand ]is now finally prepped and ready for blasting. Just looking around for a good price !!
Wheel [fr ] still giving me grief as I don’t want to damage the “flats” on the spindle – may need some heat.
beachcomberParticipantThanx to the anon person who dropped the engine parts list through my door today !!!! { Trevor ??? ]
Sorry I missed you …… another day.
And the rear wheel ???????????
beachcomberParticipantHi all
This is the front wheel that came in my bike.
There doesn’t appear to be any mods – spacers, brackets etc. IOW it’s a straight fit in.
Thoughts are it is a rogue wheel ……………any ideas ?
beachcomberParticipantKK – yes, my graffix software is now up and running again, so I’ll archive [ as I do ! ] the progress and flag up relevant pix.
beachcomberParticipantWe finished knitting up the Siamese exhaust for the “new” project [ NOT Kawasaki ! ], but had the added benefit that we ended up with a box of odd st.st. bends ! One is spot on for the right hand pipe, so looks doable without too much aggro.
Just need a tame shotblaster person in the Midlands [ ?? ]and the guy who said he would – actually come forward and weld up the Weber manifold !
beachcomberParticipantMany thanx to Trevor of this parish for bringing his immaculate ’76 round to show me this morning ………astounding, credit to you.
Also picked up many tips from a man who’s obviously been there, done that.
KK – thanx for the thought ….. as pointed out by Trevor this am – as I will be going for a daylight MOT – may as well knit myself a new bespoke loom !
Michael – my pal AC has just had a load of stainless steel tubing bent up into smaller lengths – I might get something mocked up then welded professionally and polished.
beachcomberParticipantWiring is NOT my favourite pastime anyway !!! I’ll look for a relevant loom – but thanx anyway.
Michael – yes saw that bike last year, very nice machine – definitely along those lines – not a fan of the exhaust style though !! A bit “droopy”.
-
AuthorPosts
