[Tango]

Hi Michael

Yes What You said! lol

I have never done any Carb work before so I have just Bluffed my way through! with the set up process?

Your Info sheet will be very helpful in the future.

She seems to be running Fine to me, but I don’t know these bikes, so I want KK to have a Go and give me some feed back.

I am looking forward to meeting you and the others on the Meet in June.

It would be an honour if you would see your way fit to giving her a ride and giving me some feed back at the meet.

Thanks for all your Help Michael.

[Tango]

So for those interested

My Bike is a Kz750 B1 (1976)

Its running a standard 750 CSR Exhaust

I have upgraded my Carbs to Kawasaki GPZ500s units so they are more reliable and more economic than the standard ones.

To do this I had to swap the standard 38mm inlet rubbers for ones off a 750 CSR these match the 34mm Gpz Carbs.
I have also had to set up a Choke Cable on the bike. I used a universal pull & twist car type used on old Mini’s

My Carbs are also running Pod Filters as I have done away with the standard air box.

This ment that I have had to adjust Jetting and Needle settings

Main Jets 134/5

Pilot Jets 40’s

Needle setting is 3rd notch up from the bottom.

I have then set my air screws to get the best running I can & then Balanced the Carbs.

This seems to give me quite good running. Well I’m happy and my bike now feels quite smooth. But I will have to get some miles on her as Michael said in a previous reply.

But If I have to make any other changes I will make sure I post them on here.

I hope I haven’t bored you with my obsessive posting of work I’ve done & that this information is of some use to somebody If not now maybe it will be in the future.

[Tango]

Thanks KK

Michael Thanks for the words of wisdom, always gratefully received off your good self. :O)

I have had some work to do on the Carbs,as the bike was not running well enough to Ride more than 3 or 4 miles. As the bike would not pull away unless you gave it lots of throttle, and it was bogging down.

So after trying to adjust the Carbs through the Air Screw on the bottom of the carburettor to try and richen up the mix, But this was with limited success! It was apparent that the Pilot Jet was going to have to be swapped out for a Bigger one.

I have now taken out the 35 Pilot Jet, and swapped it for a 40. But with this change the needle clip had to be raised up a couple of notches,so the needle was slightly longer. This means the fuel mix will weaken just a little. I had to do this because what I found with the 40 Pilot Jets and the Fact that I had put my Needle clip to the last possible notch to make my fuel mix richer.
This was to rich with the 40’s and the bike was over fuelling on run off as you let go of the throttle and stalling the bike.

[Tango]

Your Always Busy Kk

Good news on my twin I have been stood down from work a couple of days this week. So I have put the time given to me into the Bike

I am now pleased to let you all know that the bike has been for MOT and she Passed! So I went and taxed her straight away. So now after many years she is back on the road fully legal!

I do have some fine running issues to sort out? But that’s what you get for using non standard Carbs, But im Sooooo close. I will have it running sweet as a nut in no time at all.

[Tango]

Hey Beef how’s it going?

Nice to see another local Twin 😉

[Tango]

Stop being a Tart! ….

Although my right leg is bloody aching this morning! lol

I have decided to take the tank off & have a look at that rocker gasket, there may have been a little air leak on that as there where some very fine bubbles visible.?

I’m also going to drain that fuel out of the Tank and swap the fuel tap over to a single outlet one, as the GPZ Carbs only needs one fuel pipe! and before the tank goes back on maybe we could have a look at the Carb synchronisation to make sure that’s ok to. 🙂

So that looks like I’ve got my weekend planned out!

[Tango]

This is the post that I have found on what jets I had fitted in the GPZ Carbs

Ok I have stripped down the GPZ500,
Cleaned them up and checked what jets are in them,and they seem to be 134 main jets and 35 pilot jets,
the needle is on the 4th clip down?

Any Help on this would be helpful the bike is running Pod filters and a CSR 750 Twin Standard exhaust.

[Tango]

WooHoo!

Battery came in for the start of the New Year. And it has been fitted today!

After Some Kicking and Panting!

The old girl fired into life under her own power, for what must be the 1st time in Many Years!

I have to book it in for MOT now ….And It looks like ive got some Carb work to sort out? as it was Popping and Farting back through the carbs. KK thinks it may need bigger idle jets?

[Tango]

Wow
That’s some transformation.

Well Done that Man.

[Tango]

Bwahhhh Haa!..

Just Nearly spat my coffee across the room!… :O)

[Tango]

Thanks Michael

I can Get onto work now and try and get those dates.

[Tango]

Well Nothing else has been done to my twin.

But I have now Ordered my Battery for it a New MotoBatt one as KK says these are much better, and I shouldn’t have any problems with one of these, and they are only a fraction more expensive.

I am getting a little nervous that I haven’t got my Twin on the road yet, and Im talking about taking her over seas within the next 7 months! GULP!!

But what with the New Main Wiring loom & Clock loom. New Ignition and new Switch gears both sides! Im hoping that I shouldn’t have any problems. I just need to get it on the road and give the GPZ Carbs a try just to make sure all id well with the conversion that I have done.

The only thing that I am worried about is will the old Points and Condenser be ok on such a long trip, with possible rain and damp issues?

I guess I’ve got January and February to give that a Good testing!

Better get her on the road!

[Tango]

Hi Guys

Have we had any further conformation on the date for this meet?
I need to try and book the annual leave I will need by the 1st week in December to be in with a chance of getting the time off.

Our company makes the whole work force put in there full years annual leave entitlement by the end of the 1st week in December. So if I don’t know Ill just have to have a stab in the Dark & hope its right?

[Tango]

Hmmm This sounds Good for me.

I just need to get the dates set in stone.So I can get my holidays booked asap from the 1st of December.

[Tango]

Hi Marco Nice looking bike.

[Author]

Posts