Forum Replies Created
-
AuthorPosts
-
beachcomberParticipantJust in time for Summer !!
beachcomberParticipantSo – update on progress, with some explanatory [ I hope ] pix.
Just to clarify my thinking on the Gixer externally driven pump – Bit of imagination required !
First – the general layout – the Gixer end housing will bolt to / through the small circular alternator cover, giving me access to the alternator fixing screw which will require a slot to take the spade end of the Gixer spindle [ shortened to suit ]. That gives me both a bearing and seal for the drive. That in turn will allow me to use the stock Gixer drive sprocket and chain.
Finally the pump itself will have weld bung AN fittings welded in place.
While I was out there freezing – I decided to have a rough POC on the exhaust system using some random bends and a 2>1 collector I’d bought.
Again – imagination required – as it will be on the other side [ probably ]. As it’s a real mission to turn the bike round now, I decided to go ahead on the side I had access to ! I can see with very little mods – it’s definitely a goer. Unfortunately not with my welding ::) Nothing has been cut or modified yet – and already it almost falls into place. Someone’s smiling down on me. This side would probably “look good”, but there’s too much going on in that area with the pump, hoses, turbo etc. Although it would give me a better line into the turbo housing. At some point in the near future I have to get the rolling chassis off the bench and onto my bike lift !!
beachcomberParticipantLatest Chinese Take-Away ………
£14.00 delivered ! The 4 alloy fittings alone from UK source £16. And here’s the actual fairing [ without aperture ] £60 + screen.
beachcomberParticipantSO THE INTERNAL PUMP LOCATION IS A NON STARTER !!!!
OK, plan B …. The external location driven from the end of the alternator screw is definitely a goer.
Even sorted out the drive – thanx to Kenny and the loan of more bits ! So I looked at the end of the Gixer pump and thought – “use the end with the spindle / cog”
Yep that works a treat. Gives me a housing with bearing / seal – simple bolt on, and has the advantage of using the Gixer drive chain. It simplifies my ” can you make that for me please mister” list as well. “All” I need is the OEM Gixer drive spindle shortening and a slot machined in the alternator screw for the drive. Not quite as simple as that – but nearly so. Just as well I have THREE Gixer pumps.
Major session in the shed today. Once the pump location was sorted, a lot of the other packaging fell into place. By moving [ oh futtox ] the carefully laid out and constructed under seat electrics and tray [ !! ] I can move the turbo up and back sufficiently to get a gravity return to the sump of the turbo oil – that also means I don’t need a scavenge pump – or remote sump. Might bring a new meaning to the phrase “roasted nuts” …………… need a good source of heat protection !
Pulled the pin on the Norvil half fairing and tinted screen, and I’m 99% certain about the Manx tank cover.
beachcomberParticipantThe Flat Tracker “Tangerine Dream” is finally morphing into “Glemseck” – the Sixties style Cafe Racer – Turbo’d !
I already have some old style Tarozzi clip ons [ correct size ! ]and a choice of seat bases, although I’ll probably go with the AJS 7R style.
I’m just waiting for some measurements to come through before committing / ordering the following.
The fairing top will give me somewhere to hang the various gauges [ boost, oil pressure for Turbo and engine ]and eventually nitrous oxide paraphenalia. Maybe even the NOS bottle.
The Manx “tank” is in fact a cover only. That means I can use a stock steel KZ tank without having to worry about ethanol etc., but still have the styling I want.
I will be on the lookout for the smallest tank that will fit [ one of the custom jobbies ? ]and of course the cosmetic condition is irrelevant – in fact the more battered – the cheaper – I can use that. As long as it’s sound and petrol proof it will do.
Big shout out again for Kennys for the loan of sump and various bits so I can continue the mock up.
beachcomberParticipantMichael,
first off – thanx for sharing your build and with superb pix !! Better than a Haynes manual.
Of course, this is very helpful for my own little Glemseck project as I am completely new to the KZ 750 engine.
re: valves / different materials.
This is common practice with Hi-Po US V8 engines. The head area is an alloy to protect against heat, whilst the stem does not require such treatment .
It was also used way back on my Norton International engines. The exhaust valves [ Manx and Inter ] were sodium filled to combat extreme heat.
I remember “clipping” an exhaust valve and it cost me a week’s wages to replace it [ 1963 ] ! The change in material was obvious on the new valves, which were also “swirl” polished in the head area.
Thanx again for sharing.
beachcomberParticipantI think I’ve located a suitable remote oil pressure relief valve [ turbo supply ]. The Gixer pump puts out 55 psi before the bye-pass opens – I only need 35 ‘ish for the turbo supply otherwise seals will suffer.
The Aussie one is £169 + carriage [ £20 ]
Take a look at the very similar layout of the Mercedes 420 version – £28 !!!!
A supplier in Birmingham [ UK ! ] has them in stock. Only 15 miles away so I plan to call in and have a good look at one.
beachcomberParticipantThis is what £18 gets you from Chinabay ! 8)
SUPERB quality – complete with it’s own foam case.
Definitely erring towards the Gixer pump now. Hoping there’s room inside, if not – it’s an external setup.
A few more bits from Chinabay and I can start laying the parts out for a proper look see.
Slight terminal inexactitude on the price of the cooler – I forgot I upgraded to swivel fittings £29.00 delivered.
beachcomberParticipantSome advice please – how good is the later electronic ignition system ?
I have two options to explore – an add on electronic package to control the timing curve, rev limiter etc. – or a replacement system.
I need to have the option to retard the ignition at maybe two points ( max turbo boost and nitrous oxide activation. The ability to fine tune the advance curve would also be beneficial.
beachcomberParticipantMichael,
yes my engine IS in a very poor external condition ! I hope to be pleasantly surprised when I look inside !
However, I have been soaking it every week or so for the past 3 months with engine de-greaser to loosen the worst of the mess. All that loose stuff is off now – not too bad at all.
I have a Soda Blasting pot which I plan to use before strip down. My pal has a big beast compressor if my “hobby” unit does not have enough pressure.
Electric pump – this is a last preferred option.
Yes, pump on with ignition on [WITH activated light ]-BEFORE starting. This way I have a supply of oil to the turbo before it runs.
That also means I can run cool oil through the turbo after the engine stops running – like my old Alpine GTA Turbo.
I have asked the manufacturers of the pump for the specs – particularly pressure. I already have volume – 14 litres / minute.
Without question – the Gixer oil pump is the best solution, internal preferred – external if I have to.
Yes, you have it exactly – driven from the same spindle as the OEM pump. ALL that depends now on the distance from the mounting face [ see ChrisLWG’s set up ]to the centres of the drive wheel. As long as that distance is GREATER than the centre to the Gixer pump, I can use that drive.
Of course, I have not taken into account the electrical requirements yet ! You KNOW that I am an electrical imbecile !
beachcomberParticipantAnd as a stand by – I pulled the trigger on one of the Chinabay electric pumps. Courtesy of a bit of spare cash from the Volvo garage parts sale !it arrived FOUR days later and is very substantial and well made.
Now I have several options to the Turbo oil supply question.
The pump won’t be wasted if I don’t get to use it on the bike project – as it will see duty on my supercharged Volvo 940 Estate project. Yes, another ongoing plaything !
What isn’t obvious from the pic is the the size and weight ! It must be about 4lbs and around the size of the KZ starter motor !
beachcomberParticipantI have made some space in my garage [ and some much needed funds ! ]by selling off my V6 Volvo engine and gearboxes [ x 3 ].
That means I can now actually get to my bike ramp AND my old KZ engine, which is sitting on it !
So next job is to drain the engine, whizz the sump off and have a good look at the OEM oil pump and more important – the space I have to play with. Hopefully that will tell me if the internal siting of the Gixer oil pump is a goer or not. That is much the preferred option – but I have to see if it is practical.
I’ll also remove the other covers to get a better idea of the condition inside.
beachcomberParticipantHere’s a rough schematic of what I have in mind.
beachcomberParticipantI want to look again at my first idea to mount the pump internally [ similar to ChrisLWG ] – which way does the sprocket rotate in this view ?
The kicker will be if there is sufficient depth from the mounting face [ as Chris ] to the sump base AND the centreline of the OEM sprocket drive.
Carsten has showed concern [ valid ] about the pressure being taken off solely for the turbo. The pump is regulated to bye-pass at around 55psi – too high for the turbo [ 35psi ]. But I have already thought about this and have a couple of options – a lighter relief spring to release at say 40 psi – or a restrictor / regulator in the feed. There will be a pressure gauge situated at the turbo oil intake to monitor the situation.
The high volume is not a problem as it only feeds the 1 ltr oil cooler.
None of this is written in a workshop manual !!!
beachcomberParticipantI hope this now starts to make sense.
Drive from alternator centre screw, but will require an oil seal on the cover plate – maybe a new plate ?
I was going to get a sump made for the turbo oil return [ quote £55 ]- then came across this on Chinabay – £25 delivered !
Schematic for oiling system now roughly sketched and just waiting for my approval !
And a NEW oil cooler WITH 10AN swivel hose fittings … £29.00 as opposed to £37 for the fittings alone in the UK to modify my s/h cooler.
-
AuthorPosts
