beachcomber

Forum Replies Created

Viewing 15 posts - 76 through 90 (of 384 total)
  • Author
    Posts
  • in reply to: Uprated progressive fork springs and clutch springs #4303
    beachcomber
    Participant

    I’ve had no interest in either sets of springs – so that’s a non starter.

    I’ve found some uprated Barnett clutch springs, but they’re only about 10% uprated – not really what I need for the Glemseck project, but cheap enough for the TD [ £20 / set ].

    I’ll probably pull the old pals act and get my tame spring man to wind up a set of progressive springs for my project. He owes me big time for work I’ve put his way  – so time to call in  the favour !

     

     

    in reply to: "Glemseck" [ and maybe "Tangerine Dream" ] #4302
    beachcomber
    Participant

    It’s been very quiet in the shed recently.

    I have a dear old pal who is currently fighting cancer and I’ve spent the past 6 weeks or so taking him back and forth to hospital and ferrying his wife to visit. That hasn’t left a lot of time [ or inclination ] to get on with my hobbies.

    He has one final operation this coming weekend [ hackers allowing ] to try to save the situation – and a lung !

    He was scheduled to have the op last Friday – the day the NHS was hacked ! So that didn’t happen.

    The down time has given me time to think carefully about my options with the KZ project.

    Without being morbid – his current situation does bring up the matter of mortality – and “useful time left” on the meter.

    So I will concentrate on completing the “Tangerine Dream” to try to get myself on the road as soon as possible and at the same time putting together the turbo “Glemseck” version as time and funds allow.

    His current bout of ops will have a 9 week recovery time, but he will be allowed home after a week, so that means I won’t be on the hospital taxi run for his Wife’s visits [ 36 mile round trip ].

    Hopefully I will be able to report some useful progress from next month.

    in reply to: Uprated progressive fork springs and clutch springs. #14160
    beachcomber
    Participant

    To date I have the following info. on OEM and uprated [ Barnett ] clutch springs.

    I’ve found new OEM springs at £7.00 each + p&p.

    Barnett uprated [ 10 – 15% ] £43.50 [ from the USA ] but that doesn’t include any customs duty or VAT. That’s for a set [ 5 ].

    I’m looking at 20% minimum uprated.

    In minimum quantity it looks like around £5.00 per spring [ 20% uprated ].

    in reply to: "Glemseck" [ and maybe "Tangerine Dream" ] #4193
    beachcomber
    Participant

    OFFICIAL – two bikes ….

    yep, Kaptain Kwack to blame – he’s a terrible bad influence on me – FORCING me to do a second bike !!!

    So, work now continuing on the “TD” Flat Tracker and when my pal comes back from a short break next week – it’s up to the garage with it and on to the ramp.

    I have “found” where my spare [ !! ] IHI Turbo went to – a pal borrowed it a few years ago for a BMW Oilhead project we were working on. He’s dropping it off at the weekend. There is a good chance that it is one fitted with a carbon seal – which means it can be used for a suck through set up with an SU carb.  Much simpler, and in my comfort zone of expertise.

    Once I have the new frame / swingarm and “race” engine from KK, I’ll start mocking it up of the bench from where I left off.

    I have a head start inasmuch as all the “whatifs” have been carried out on the TD.

    I do like the exhaust I mocked up, so I will need to get another set of bends for the Glemseck !

    in reply to: Uprated progressive fork springs and clutch springs #4192
    beachcomber
    Participant

    I just paid a visit to my tame spring man.

    Absolutely NO problem. He has ample stocks of the correct grade high quality spring wire to make both clutch and fork springs.

    I WILL go ahead with the clutch springs anyway. I need to order 100 springs minimum, which is only 20 bike’s worth ! Just as a matter of interest I’ll check the price availability of OEM clutch springs.

    The fork springs are another matter, as the unit cost is significantly higher – not huge, but I have to be certain there is interest before I commit to placing an order. However, I expect a unit cost of less than £75 / pair with an initial order of 50 springs.

    Like I said – any interest ??

    in reply to: Uprated progressive fork springs and clutch springs. #14159
    beachcomber
    Participant

    I just paid a visit to my tame spring man.

    Absolutely NO problem. He has ample stocks of the correct grade high quality spring wire to make both clutch and fork springs.

    I WILL go ahead with the clutch springs anyway. I need to order 100 springs minimum, which is only 20 bike’s worth ! Just as a matter of interest I’ll check the price availability of OEM clutch springs.

    The fork springs are another matter, as the unit cost is significantly higher – not huge, but I have to be certain there is interest before I commit to placing an order. However, I expect a unit cost of less than £75 / pair with an initial order of 50 springs.

    Like I said – any interest ??

    in reply to: Uprated progressive fork springs and clutch springs. #14158
    beachcomber
    Participant

    KK – as ever, depends on quantities.

    I developed the K100 springs shown and initially I had to commit to 20 springs [ 10 bikes ].

    However, when the sales started to grow I could order in greater quantities [ 100 springs ], bringing the price down considerably to sub £75 / pair retail.

    However, they were developed over 5 years ago, I will call in on my tame spring man as soon as I have a sample clutch spring to show him. I already have a stock KZ spring from my bike.

    For the air assist spring replacements I will need some sort of spec / sample.

    Incidentally, these springs are made from the same Swedish spring steel that top aftermarket spring manufacturers use.

    I need to go ahead with the clutch springs anyway, but of course it doesn’t make sense to have just 1 or 2 sets made !

    in reply to: "Glemseck" [ and maybe "Tangerine Dream" ] #4136
    beachcomber
    Participant

    Might actually be TWO if KK has his way !!!!

    We’re now looking at the original Tangerine Dream Flat Track version [ mild road ] as well as the Glemseck project which seems to be morphing into a Drag / Road bike !  The plan is to pursue the Flat Tracker – as in reality it was virtually all there before the moment of madness – in an effort to get myself a road bike sooner rather than later.

    I have to realistic with the Glemseck project – there are quite a few bits which I will need to get made – which will eat up favours and money ! However, I have NO intention of cutting any corners with this project.

    in reply to: Got a new project #14156
    beachcomber
    Participant

    Welcome aboard David.

    I’m sure you’ll find the bits you need in Kaptain Kwacks huge stock !!!

    in reply to: Hello lonesome´s, a further member from Germany is online #3653
    beachcomber
    Participant

    Hi Gerd,

     

    good to see some more of our German cousins here – welcome.

    in reply to: Glemseck – thinking aloud #13805
    beachcomber
    Participant

    I actually started dismantling my engine yesterday – I managed to get it onto a temporary “clean” bench”.

    Temporary as I want to clear my main bench [ a mess ! ]before total dismantling takes place.

    Curiosity as much as anything else – just removed case covers to see what’s actually inside !

    The engine looks like it has been freshly assembled – which is in line with the info from the PO.

    However, it now shows me that the outer casing [ alternator ] is one piece – and NOT with a removable central cover !! Cunning Japanese put the three screws there to fool me !

    That actually makes the conversion simpler as the three screws are equidistant to the crank end. So the drilling of a drive spindle rod hole is simple to get “right”. I now understand Michael’s warning of a “dome” !

    My engine has the smaller screw and of course a different set up for the alternator.

    The good news is that my new engine is a later model with the larger screw and electronic ignition.

    I have several possibilities to locate the pump now, and I can also drive it from either side.

    So, I won’t waste any more time on that at the moment, but wait until the bike is on the bike ramp and I can gain access all round. Then it will become obvious [ ?? ] which is the most practical location.

    That also frees up decisions re: the exhaust – which side etc.

    I have quite a lot to package into the bike – turbo, Nitrous, exhaust, pump etc.,etc + all the relevant switches, gauges and controllers – so I think the plan now is to get it on the stand and start looking at where everything is going to live.

    in reply to: Glemseck – thinking aloud #13804
    beachcomber
    Participant

    Thanx for the very useful graphic Michael.

    I imagine the crankshaft must also be changed to use the larger screw !

    One alternative we used on some V8 Ford engines where a particular screw was marginal – was to swap for a stud.

    In my case I have to make provision for a spade drive [ from the Gixer pump ]so a slot will be required anyway. A stud from suitable material might be the answer ?

    I have another engine coming from KK at some time, so I will check that one out.

    A pal is loaning me an engine crane next week [ supercharged Volvo project ] so I can use that to raise the KZ engine onto the bench and “get inside” – for the very first time !

    in reply to: Glemseck – thinking aloud #13803
    beachcomber
    Participant

    Ha,ha Michael !!!!!! NO – it was a pal of mine who is not a forum member.

    Yes, The ign side was my first choice because of the “dry” area.

    However, the drive spindle is very small and we have an issue with the direction of rotation. If I use the spare Gixer pump outer housing there is a seal and a bearing. I will do a sketch next week to explain. It does look very practical.

    Thanx for the headsup on the different screw sizes. There is not much inertia to overcome from the pump.

    Please keep your input coming Michael – always appreciated.

    in reply to: Glemseck – thinking aloud #13802
    beachcomber
    Participant

    A friend asked me why I post so much AND change my mind often !

    I prefer to think of it as “evolution” and the reason for posting – I get valuable feedback from some of you experts – which is much appreciated.

    Latest “whatif” …… The exhaust will definitely be better suited on this side. Michael,I understand your comments about “display” and leaning to the left. I think I am reaching the point where a paddock stand might be needed!

    However, that puts the exhaust / turbo in very close proximity and might cause heat transfer problems.

    There is room ( and shorter chain run ) if I mount the pump in front of the lower frame rails – level’ish with the sump. It will require protection of course, but I have a solution for that which is”different”, and will look good.

    So, apologies to anyone who thinks I post too much ………..

    in reply to: Glemseck – thinking aloud #13801
    beachcomber
    Participant

    Today was a general checking out of my theories [!].

    I also finalised the POC fitting of the exhaust.

    By no means finished as I have not yet cut / modified any of the random bends I bought. I want the “welder” to check everything out first.

    So, imagine the front pipe bends much tighter to the head and the 2 in to 1 collector will be parallel with the two pipes – just to clean up the aesthetics.

    I have a good run into the turbo from this setup, but of course that cannot be finalised until the oil pump / hosing is in place. I still have the option of repeating this on the other side.

    Now I don’t have to use the oil sump I bought [ !! ], I now have some extra space for the battery [ under swingarm ].

    I will have to remove my electrics undertray and re-site all the components [ drat ], but that’s just an annoyance rather than a problem.

Viewing 15 posts - 76 through 90 (of 384 total)