beachcomber

Forum Replies Created

Viewing 15 posts - 301 through 315 (of 384 total)
  • Author
    Posts
  • in reply to: Flat Tracker #10198
    beachcomber
    Participant

    Undertray fettled and part fitted, all threads chased out and stainless fixings sorted.

    I’ve also made a start on some of the controls and brake parts etc. All wire brushed and a first coat of textured matt Black applied …….. we’re on the way now !

    Now, if only I could find where I put the engine plates for safe keeping !

    HAs anyone got some spares just in case ???

    in reply to: Flat Tracker #10197
    beachcomber
    Participant

    Well here we are a week later and STILL waiting for the “new” powder coaters to perform !

    On the plus side, my pal AC has cut and bent the alloy under tray – just waiting for my new aircraft snips [ LH,RH and straight £12.95 THE SET- EBay ] to arrive and I can put the final fettling cuts in.

    in reply to: Flat Tracker #10196
    beachcomber
    Participant

    I’d hoped there would be some nice pix of the newly p/coated forks assembled by now – but I live in hope rather than expectation !

    I found a new powder coaters – who promised all sorts of wonderous service and good prices AND who could do the work in days rather than weeks …………….. left the fork bottoms there nearly 2 weeks ago, only to get a phone call yesterday to tell me “they couldn’t match the colour” [ to the frame etc ].

    Pointless telling them the other parts were done by a company – not a mile away !

    Ah well ………. I’ll drop the fork bottoms in to my old p/coaters at the weekend. Again, they are up to their asses in alligators with “proper paying” work, so yet another delay of a week.

    One good result – the fork stanchion tops [ in between yokes ] were quite badly pitted, and I naturally assumed that the fork gaiters were hiding more horrors. oh thou cynical one ……. not a bit of it, when I got the forks stripped and lower stanchions exposed, they were fine !

    Not only that – but the fork oil had obviously been replaced and there were new seals and evidence of recent work – recent as in before the bike was left to rot outside.

    Those who saw the “as bought” pix and laughed like drains and said “you’re building THAT ” – along with myself I might add – like me, would be surprised at all the new and reconditioned parts in and on the bike. The tank has been professionally cleaned and sealed inside, and when I took the valve cover off – the inside was clean as a whistle with new oil and gaskets obvious everywhere.That along with new wheel bearings etc. lead me to suspect that the seller wasn’t telling porkies when he said the guy HE bought it from had told him it had been refurbished. mechanically.

    in reply to: Flat Tracker #10195
    beachcomber
    Participant

    Thanx for the encouragement KK,

    Yes, it’s good to be able to report some actual progress on the bike. rather than the peripheries.

    No real excuses now, oh – except for the having to wait for other peeps to do specialised outwork I can’t do myself !

    in reply to: Flat Tracker #10194
    beachcomber
    Participant

    Electrics under tray pattern made – thanx Kellogs.

    Shotgun lamp mounted and seat to frame mounts finalised.

    Wheels finally back and powder coated – yipeeeee. Excellent job for £35 a wheel. New wheel bearings ordered.

    Forks stripped ready for bottoms to be powder coated the same Red as the frame.New fork seals arrived yesterday.

    real progress at last !!!

    in reply to: Flat Tracker #10193
    beachcomber
    Participant

    And so it begins ………………

    in reply to: Flat Tracker #10192
    beachcomber
    Participant

    This is the last non bike pic …. honest !!!!

    All ready to go now ……… KZ frame and parts coming down on Monday for the detailing and sub assembly.

    I need to make up an electric under tray [ seat ] and fit the Shotgun rear lamp [ stop only ]. Then it’s fit new headstock bearings, strip forks out [ powder coat bottom legs ] and generally try to find all the parts !

    I’ll also make a start on the tank and pother parts that need prepping for paint.

    I hope to have the engine down to the guy who is welding up the 40DCOE Weber manifold in the next two weeks.

    Wheels are finally going off for powder coating with my pal’s stuff next Friday.

    Progress at last ………..

    in reply to: Fork stanchions wanted #12389
    beachcomber
    Participant

    KK,

    sorry for the delay in responding – been one of those months !

    You know I have the weird wire wheel – will it fit ?

    I only really need stanchions as the legs have been sent off for powder coating and I have new seals and springs.

    Thanx as always

    TJ

    in reply to: Flat Tracker #10191
    beachcomber
    Participant

    Benches now reinforced [ 30 ft long ! ]. New Pillar drill and bench grinder [ thanx Aldi ] will be mounted along with my “new” engineer’s vice [ FOC courtesy of a pal] this weekend.

    Electrics now all completed and working [ my own fair hand ] – just the fluorescent light fitting to go up then we’re ready to boogie.

    First job is to get the frame and parts down from the garage and checked out – new headstock taper bearings and a few odds [ like under seat electrics tray ]. Then the forks need to be stripped as I’ve decided to have the lowers powder coated in the same FO Red as the frame.

    Anyone got some decent fork stanchions? Mine are “borderline” rubbish !

    The guy who volunteered to make up the 40DCOE Weber intake is keen – he’s rung me 3 times to ask when I’m taking the engine and flanges round ! Very, very soon now.

    Wheels …… ah the wheels. My pal and I are working on another project [ Modern Cafe Racer BMW Oilhead ]and the wheels for that will be Gold powder coated – so we’re taking them all in together – next few weeks.

    in reply to: Flat Tracker #10190
    beachcomber
    Participant

    Thanx for that Lonesome …… I’m trying to strike a balance between “being chatty” with progress and abusing the “no new info.” scenario.

    Anyway – progress / non-progress.

    After TWO failed attempts at getting a friend of a friend round to do the electrical work in my new “workshop”, I’ve given up and ordered the materials I need and I’ll have a go myself.

    However, the benches are now installed [ ‘ish ], but I still need to reinforce them – legs and worktop. I’m not disappointed – for less than £50 I have a good basis for a 12 foot long bench / work surface ! More than enough to get my new [to me ] engineer’s vice, grinder / belt sander, pillar drill [ !!! ] set up with plenty of room for sub-assemblies etc.

    As it was [ next door’s shown ] and part finished project.

    Oh yes …… and the wheels – hmmmm. My tame powder coaters have been inundated with work and you know what it’s like when folk are “doing you a favour” ! They’re definitely going in end of next week.

    in reply to: Flat Tracker #10189
    beachcomber
    Participant

    Well – big slow down after all the relative progress [ progress report ].

    My Dobe’s toe amputation [ really !! ]had complications which has seen me back and forth to the vets – fortunately covered by insurance [ £850 ].

    That meant that the lean to workshop stalled out – although the end has now been covered and secured and the roof panels completed courtesy of a pal.

    My Daughter and her partner [ been living with us for past year ]are finally moving in to their new house at the end of the week. How’s that been a hold up ? Well, their THREE bicycles are currently stored in my lean to which means I can’t get the benches / etc. set up until they go [ weekend ].

    That’s my excuse anyway………….

    in reply to: Wheels #12247
    beachcomber
    Participant

    And the price for the wire spoked alloy rims is ??????????????????

    in reply to: Flat Tracker #10188
    beachcomber
    Participant

    You keep collecting KK !!!!!!!!!!!!!!

    At least we all know where to get our spares.

    Wheels finally going off this coming week – I just have to check Monday morning to make sure they have finished their customer run.

    Believe me, I would LOVE to post pix of some nice blingy Gold wire rimmed wheels !

    Then I have to pull the forks apart so I can get the bottom legs powder coated Red to match the frame etc.

    Anything to watch out for oh wise one ?

    Actually the stanchion tops are a bit pitted [ cosmetic ], so maybe I should consider some better looking ones. Alternatively. I could have the top section powder coated [ gaiters on the bottom ].

    Thanx to everyone for the encouragement.

    in reply to: Flat Tracker #10187
    beachcomber
    Participant

    I have all my new bearings now [ KK thanx for the timely reminder ]all ready to be installed.

    Not so good news is that the powder coaters have had a huge run for one of their major customers, so wheels still awaiting treatment ……ah well after 12 MONTHS [ !! ] what’s another week or two ?!

    I’ve also decided to have the fork leg bottoms powder coated in the same Red as the frame.

    My log store [ lean to workshop ] is now nearly finished. That will allow me to actually work uncluttered on sub assemblies / painting / detailing etc.

    I got a couple of 4 ft. x 18″ workbenches courtesy of E-Bay – £50 delivered !

    Not the most robust in the world, but by the time I put a couple of ex.kitchen worktops on and beef up the sides – good to go.

    in reply to: Flat Tracker #10186
    beachcomber
    Participant

    A bit off beam here – but related………….

    When I was researching the bearings for the Yamaha, the old chestnut [ new chestnut? ] of parts made in the Far East / China etc. versus “proper” parts made in Europe came up.

    Oh no they’re not !!!! ALL the well known marques [ SKF, FAG, etc ] are now manufactured in plants outside their country of origin ! Most in China / India and one well known North European bearing marque is manufactured in Portugal.

Viewing 15 posts - 301 through 315 (of 384 total)